null

GForce MOP10907A-Alum Modified Cradle Service & 9" IRS Kit for 09-14 Challenger, Charger, & 300C

Product Code: MOP10907A-Alum
(No reviews yet) Write a Review
Share:
$5,804.00
High Horse Performance is Veteran Owned & Operated
Description

***Driveshaft is no longer included, you will need to source your own. Measure once the 9" conversion is installed.***

***2015+ SRT / Hellcat Rear Cradle is Required and available separately MOP10416C.***

***Strange HD Pro Aluminum Center Section is also sold separately with your choice of Gear Ratio GPE10302A.***

The GForce Engineering 9” IRS for the 09-14 Dodge Charger and Challenger Hellcat, SRT and Scat Pack is a independent rear suspension that replaces your drive-line from the transmission back. Includes a fabricated 9” housing that bolts to the stock differential mounting points. It also includes GForce bullet-proof Renegade or Outlaw axles, 35-spline inner stubs, new outer stubs, and modified rear cradle service only. Cradle sold separately. 

What makes this kit different than most 9” kits we offer is the modified cradle assembly. In many cases, we strive to make the 9” a “bolt-in” solution that fits into the factory cradle and uses factory mounting locations. However, with the Challenger and Charger, we found there to be several geometry limitations that were proving to be weak points in such a powerful and heavy application. It’s not a secret that the cradle and suspension design in these cars is a dated design. The location of the differential, less-than-desirable axle angles and very soft bushings were causing premature wear and failure in many of the drivetrain parts; including axles, differentials and driveshafts. This problem was only magnified when lowering the car, going to a taller tire or softer springs allowing for more compression on hard launch.

In 2015, Mopar made a small modification to the rear subframe (cradle) on this platform, adding a second front mount. Now you have 2 rear mounts and 2 front mounts which is an improvement over the 05-14 cradle that only included a single front mount for the differential. Our first step was to create a jig that would allow us to strengthen and modify these cradles to reposition the differential higher in the vehicle. This allows for optimal axle and pinion angle, even under load. This also eliminates excessive wear on the CV’s due to angle and axle centerline. Due to the success of this design, a completely new rear cradle is a part of the GForce 9” kit. These are made from brand new OE Mopar cores. In addition, with each cradle, we go to the trouble of removing all of the OE rubber bushings from assembly. We press in beefy, dual-stage poly bushings into the cradle to body locations and billet aluminum center section bushings.

Purchasing this kit is a lot more than just a center section, axles and driveshaft. It truly is a new driveline; complete with a new, modified subframe, cradle and differential bushings, improved geometry and everything else you would expect from a GForce 9” kit.

9” Assembly:

  • Fully fabricated 9” housing – One-piece, laser cut, CNC-bent and tig welded for flawless finish and unmatched strength
  • Heavy duty front mount
  • Your choice of our Renegade or Outlaw axles
  • 35 Spline Inner Stubs – One piece, CNC-Machined from billet steel
  • Upgraded outer stubs
  • Strange Engineering Pro-HD Aluminum Third Member with 35 spline S-Trac Differential – Your choice of gear ratio
  • All necessary hardware for installation

Rear Cradle Modifications:

  • All labor for modifications (welding, bushing removal, paint, etc.)
  • New 2-stage, poly cradle bushings (installed)
  • Billet aluminum differential bushings (installed)

Note: Kit is available for the 09-14 Charger, Challenger and 300C. Will require the same 15+ subframe as indicated above. (included with purchase) See notes on installation below.

2009-2014 Mopar Platform:

  • Uses 15+ style exhaust mounting points
  • Factory 2-piece, passenger side carrier bearing mount in the trans tunnel will need to be clearanced or removed.
  • The 06-14 control arms fit very tight around the CV’s and they will make contact at full droop (which is normal of many aftermarket axles). However, the newer 15+ “Hellcat style” lower control arms have more clearance around the outer CV and might offer a little more peace of mind for daily abuse.
  • Axles require the SRT8 style 32-spline outer hubs (some of the earlier cars were a lesser spline count. Upgrading to the newer 35-spline, 15+ hubs is also an option. (Any modifications such as this will need to be noted when placing the order)